Classe Audio SSP-800 - V3.3 Owner's Manual download pdf (Page 75)

38-EN

• The CD is being improperly inserted.

– Make sure the CD is being inserted following instructions in the

CD Player Operation section.

Unable to fast forward or backward the CD.

• The CD has been damaged.

– Eject the CD and discard it; using a damaged CD in your unit can

cause damage to the mechanism.

CD playback sound skips due to vibration.

• Improper mounting of the unit.

– Securely re-mount the unit.

• The disc is very dirty.

–Clean the disc.

• The disc has scratches.

– Change the disc.

• The pick-up lens is dirty.

– Do not use a commercially available lens cleaner disc. Consult

your nearest Alpine dealer.

CD playback sound skips without vibration.

• The disc is dirty or scratched.

– Clean the disc; damaged disc should be replaced.

Error displays (built-in CD player only).

• Mechanical error

– Press . After the error indication disappears, insert the disc

again. If the above-mentioned solution does not solve the problem,

consult your nearest Alpine dealer.

CD-R/CD-RW playback not possible.

• Close session (finalisation) has not been performed.

– Perform finalisation and attempt playback again.

MP3/WMA is not played back.

• Writing error occurred. The MP3/WMA format is not compatible.

– Make sure the MP3/WMA has been written in a supported format.

Refer to “About MP3/WMA” on page 13, then rewrite in the

format supported by this device.

The sound is not output from the speakers.

• Unit has no output signal of the internal amplifier.

– POWER IC is switched to “ON”, refer to “Connecting to an

External Amplifier (POWER IC)” on page 17.

iPod does not play and no sound is output.

• The iPod has not been recognised.

– Reset this unit and the iPod. Refer to “Initial System Start-Up” on

page 10. To reset the iPod, refer to the Owner’s Manual of the iPod.

•No CD is inserted.

–Insert a CD.

• Although a disc is inserted, “NO DISC” is displayed and the unit does

not start to play or eject the disc.

– Remove the disc by following these steps:

Press the  button again for at least 2 seconds.

If the disc still does not eject, consult your Alpine dealer.

• Mechanism error.

1 Press the  button and eject the CD.

If not ejecting, consult your Alpine dealer.

2 When the error indication remains after ejecting, press the 

button again.

If the error indication still does not turn off after pressing the 

button for a few times, consult your Alpine dealer.

• When “ERROR” is displayed:

If the disc cannot be ejected by pressing , press the RESET button

(Refer to “Initial System Start-Up” on page 10) and press  again.

If the disc still cannot be ejected, consult your Alpine dealer.

• A copy-protected WMA file was played back.

– You can only play back non-copy-protected files.

• A sampling rate/bit rate not supported by the unit is used.

– Use a sampling rate/bit rate that is supported by the unit.

• A USB device that is not supported by the unit is connected.

– Connect a USB device that is supported by the unit.

• A Flash Memory Device is not connected.

– Make sure the Flash Memory device is correctly connected and the

cable is not excessively bent.

• No MP3/WMA (file) is stored in the Flash Memory.

– Connect the Flash Memory device after storing songs (files).

• A copy-protected WMA file was played back.

– You can only play back non-copy-protected files.

• A sampling rate/bit rate not supported by the unit is used.

– Use a sampling rate/bit rate that is supported by the unit.

• Text information that is not recognizable by the unit has been input.

– Use a Flash Memory device with input text information that is

supported by the unit.

MP3/WMA

Audio

iPod

Indication for CD Player (CDE-SXM145BT/

CDE-143BT only)

Indication for Flash Memory

NO DEVICE

NO SUPPORT

1 2 ... 70 71 72 73 74 75 76 77 78 79 80 ... 88 89

Comments to this Manuals

No comments

Classe Audio SSP-800 - V3.3 Owner's Manual Page 75

Comments to this Manuals

Related products and manuals for Processors Classe Audio SSP-800 - V3.3